Cleats Wiring

Cleats Wiring used to secure cable to wood or masonry.

D.W - Dropwiring
D.L - Down Lead


Colour
Black
White

Grey
Brown
Cream


Used With
Cable D.W 10B
Cable D.L 1 & Cables of 0.5 Dia.
Cable D.L 1
Cable D.L 1
Cable D.L 1

Code
1614
1615

1619
1686
1628
 

Cleats Wiring used for fixing internal cable on wood or masonary. Plastic saddle type with a captive pin.

Cable Dia. (mm)
2.75
3.5
5.0
5.0
7.0-9.0


Colour

White
White
White
Black
White


Qty.

500
500
500
500
100


Code

1616
1617
1620
1625
1623
 
Cable Tie

For general purpose use, has high tensile strength, made of nylon and packed in sealed bags. All the items listed below are black but they are available in neutral and in both colours in other other sizes.

Service temperature range:
-25C to +80C

Size (mm)
2.5x100
2.5x100
2.5x100
2.5x100
4x275
4x275
4x275
4x275
4x200
4x200
4x200
4x200
4x140
4x140
4x140
4x140
5x360
5x360
5x360
8x300
8x300
8x300
8x300

Qty.
1000
500
250
100
1000
500
250
100
1000
500
250
100
1000
500
250
100
1000
250
100
1000
500
250
100

Code
1595
1596
1597
1633
1586
1587
1588
1631
1589
1590
1591
1632
1592
1593
1594
1634
1580
1582
1629
1583
1584
1585
1630
 
Line Jack Unit

A full range of approved Line Jack Units is available most with a choice of IDC or screw terminations.

1/...Supplied with back box
Dimensions 55mm x 55mm x 29mm.
2/...Supplied with back box
Dimensions 68mm x 68mm x 29mm.
3/...Not supplied with back box, but compatible with Standard BS Fittings.
Dimensions 86mm x 86mm.
4/...As type 3/... but with two outlets for two seperate circuits
Dimensions 86mm x 86mm.
Master comes with a bell capacitor, a lightning arrestor and an out-of-service resistor for test purposes.
PBX Master (PBX) comes with a bell capacitor only.
Secondary (Sec) comes with connections only, no other components.

1/1A
1/3A
1/4A
1/6A
2/1A
2/2A
2/4A
2/6A
3/1A
3/3A
4/1A
4/3A

Master
Sec
Master
Sec
Master
PBX
Master
Sec
Master
Sec
Master
Sec

IDC
IDC
Screw
Screw
IDC
IDC
Screw
Screw
IDC
IDC
IDC
IDC


1311
1312
1314
1315
1300
1304
1302
1303
1308
1309
1305
1306

 
Plug Telephone

Supplied as 6 or 4 way plugs with a latching device on either the left or right (with contacts uppermost). Those with the latch on the right are generally used for plugging on the end of line cords for plugging into line jacks. Those with left hand latches are for handsets, but, are also used in reversed line jacks where plugging in of the wrong equipment may be detrimental to either the item plugged in or the line equipment (as in the case of certain Key Telephone Systems). Used with "D" section cord to CW1311.

Plug
431A
430A
631A
630A

Latching
Right
Left
Right
Left

Code
8535
Z-5110
8538
8223
 
Mini-Trunking Systems

Produced in a white shade which has been carefully selected. Available in popular sizes. Mini-Trunking is manufactured from an extra super high impact grade of PVC. All strips are 3 metres in length.


Size (mm)
16 x 16
25 x 16
38 x 16
38 x 25
50 x 25
38 x 38


Qty
30
30
15
15
15
15

Code
Z-0174
Z-5521
Z-5523
Z-5526
Z-5529
Z-5528
 
Mini-Trunking Systems Flat Bend


Size (mm)
16 x 16
25 x 16
38 x 16
38 x 25
50 x 25
38 x 38


Pack
100
100
50
30
20
20


Code
Z-5533
Z-5536
Z-5538
Z-5541
Z-5544
Z-5545
 
Mini-Trunking Systems Equal Tee


Size (mm)
16 x 16
25 x 16
38 x 16
38 x 25
50 x 25
38 x 38


Pack
100
100
50
30
20
20

Code
Z-5546
Z-5547
Z-5548
Z-5549
Z-5550
Z-5551
 
 
Mini-Trunking Systems Unequal Tee


Size (mm)
16 x 16
25 x 16
38 x 16
38 x 25
50 x 25
38 x 38


Pack
100
100
50
30
20
20

Code
Z-5552
Z-5553
Z-5554
Z-5555
Z-5556
Z-5557
 
 
Mini-Trunking Systems Coupler

Size (mm)
16 x 16
25 x 16
38 x 16
38 x 25
50 x 25
38 x 38

Pack
100
100
50
30
20
20

Code
Z-5558
Z-5559
Z-5560
Z-5561
Z-5562
Z-5563
 
 
Mini-Trunking Systems End Cap

Size (mm)
16 x 16
25 x 16
38 x 16
38 x 25
50 x 25
38 x 38

Pack
100
100
50
30
20
20

Code
Z-5564
Z-5565
Z-5566
Z-5567
Z-5568
Z-5569
 
 
Mini-Trunking Systems Internal Bend

Size (mm)
16 x 16
25 x 16
38 x 16
38 x 25
50 x 25
38 x 38

Pack
100
100
50
30
20
20

Code
Z-5570
Z-5571
Z-5572
Z-5573
Z-5574
Z-5575
 
 
Mini-Trunking Systems External Bend

Size (mm)
16 x 16
25 x 16
38 x 16
38 x 25
50 x 25
38 x 38

Pack
100
100
50
30
20
20

Code
Z-5576
Z-5577
Z-5578
Z-5579
Z-5580
Z-5581
 
 
Connector 226

A general purpose apparatus connector. Suitable for 50 wire 0.5mm solid wire termination. Cable entry is from the side and comes with a cable clamp and a screw lock. Both types listed are for cable end fixing.
C. 226 C50AB
C. 226 A/50AB
Female
Male
9024
9025
 
 
Part No. 8304
Ring Jumper 37B

For routing jumper wire round 300 series distribution boxes. Made of plastic.
 
Part No. 8010
Box Connection 251A

Internal distribution box that will accept up to 5 x 237 type Connection strips. Comes complete with 4 x jumper rings and an earth bar. Fitted with removable side panels with cable knockouts.

Strips Connection 237.
Strips Designation 51A.
 
Part No. 8021
Box Connection 301A

Internal distribution box that will accept up to 10 x 237 type Connection strips. Comes with an earth bar and fitted with removable side panels with cable knockouts.
 
Part No. 8026
Box Connection 200 Series

Internal distribution box that will accept up to 2 x 241B type Connection strips. Comes with integral wire guides and a 10 way IDC earth strip with 2 x screw terminals.

Number of pairs - 10
 
Box Connection 500 Series

Internal distribution box that comes complete with integral wire guides, an earth bar and backmount frames. Made of sheet metal with a door that can be fitted to open from left or right and that incorporates a document holder and fitted with a lock. The side panels have knockouts, used when next to other boxes, the top and bottom have removable cable entry panels.

Box Connection 520
Box Connection 530

8207
2011
 
 
Part No. 1970
Block Terminal 66B

Used for terminating 2 pair and 5 pair insulated cable conductors. Primarily intended for external use. Available with or without Block Insert 1A or 2A.
 
Block Insert

Screw terminal insert for Block Terminal 66B and a maintenance replacement for Block Terminal 41A and 66A.

Block
1A
2A

Terminations
4
6

Code
1971
1972
 
 
Strip Connection 237

IDC terminating module, clip fits onto frame mounting in various Box Connections. Accepts insulated conductors of 26 AWG to 18 AWG. If using wire larger than 22 AWG then only one wire can be terminated in a single slot as opposed to the normal maximum of two.

A full range of accessories are available for this product.

S. C. 237A Cream (Krone)
S. C. 237C

8025
8027
 
 
Part No. 8059
Strip Designation 51A

This is a blank white card for writing on. Including label.
 
Part No. 8323
Wedge Locking 23A

Used on Strips Connection 237 to isolate individual circuits.
 
Part No. 2128
Pouyet Strip

This protected strip accepts wires with a conductor diameter size between 0.4 - 0.8mm. The strip is mounted in a high density back mount frame that fits into a variety of connection boxes and frames.

A full range of accessories are available for this product.
 
SID Strip

The SID-C termination strip is used for joining up to 10 pairs of copper cables in voice or data networks and increase connection capacity by up to 25% without compromising the jumper space requirements.

A full range of accessories are available for this product.
 
Part No. 8302
Jack Test 45/1C

A 100 pair terminating / test access block, used on Frame Distribution 7A, 7B and 7D. Includes five point lightning protection using Protector module 1A or 2A. Complete with all fixing nuts and bolts.

227mm x 7mm x 178mm
 
Part No. 8303
Jack Test 46/1C

A 100 pair termination / test access block, used on Frame Distribution 7A, 7B, 7C and 7D. Does not include lightning protection. Complete with all fixing nuts and bolts.

227mm x 7mm x 178mm.
 
Part No. 8305
Jack Test 47/1B RNV

RNV Reverse Number Variant of Jack Test 47/1B, i.e. numbering is from top to bottom. A 100 pair terminatin / test access block, used on exhange side of a "rack type" MDF. Includes five point lightning protection using Protection Module 1A or 2A. Complete with all fixing nuts and bolts.
     
Part No. 8331
Cover 131B

Provides dust cover and additional sign writing facilities on the front face of Jack Test 44-49 series.